A: To setup Decnet plus:
$ type net$csmacd_startup.ncl
!% net$configure.com created-
!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node 0 csma-cd station csmacd-0 communication port
= eza
Enable node 0 csma-cd station csmacs-0
$
$ show device e machien will responds with e?? Ewa
To configure decnet plus to run on 100m/b adaptor
$ edit net$csmacd_startup.ncl
!% net$configure.com created-
!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node 0 csma-cd station csmacd-0 communication port
= eza [eza0 is
The old 10m/b adaptor replaces with ewa]
Enable node 0 csma-cd station csmacs-0
$ control z to exit
$
$ type net$csmacd_startup.ncl
!% net$configure.com created-
!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node 0 csma-cd station csmacd-0 communication port
= ewa
Enable node 0 csma-cd station csmacs-0
Reboot your system this will enable the 100m/b
ethenet as your primary
Ethenet controller.
If you wish to setup your network with two network adaptors,
run
Net$config and answer the questions and when it responds with
is this an Ennode or router, say its a router. Finish answering
all questions.
$ type net$csmacd_startup.ncl
!% net$configure.com created
!% ncl script sys$specific:[sysmgr]net$csmscd_startup.ncl;
!% 19-june-2001 10:46:40.95
!%
Create node 0 csma-cd
Create node 0 csma-cd station csmacd-1 communication port
= ewa
Enable node 0 csma station csmacd-1
Create node 0 csma-cd station csmacd-0 communication port
= eza
Enable node 0 csma-cd station csmacd-0
Decnet plus setup
$ type net$csmacd_startup.ncl
!% net$configure.com created-
0 csma-cd station csmacd-0 communication port = eza
Enable node 0!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node csma-cd station csmacd-0
$
$ show device e machine will respond with e?? Ewa
To configure decnet plus to run on 100m/b adapter
$ edit net$csmacd_startup.ncl
!% net$configure.com created
0 csma-cd station csmacd-0 communication port = eza [eza is
the old adaptor. Change this to ewa. This will enable the
100m/b ethernet card to run as Network adaptor.]
Enable node 0!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node csma-cd station csmacd-0
$ control z to exit
$
$ type net$csmacd_startup.ncl
!% net$configure.com created-
0 csma-cd station csmacd-0 communication port = ewa
Enable node 0!% ncl script sys$specific:[sysmgr]net$csmacd_startup.ncl;
!% 19-june-2001 15:18:24.10
!%
Create node 0 csma-cd
Create node csma-cd station csmacd-0
$
Reboot your system this will enable the 100m/b ethenet as
your primary
Ethernet controller.
If you wish to setup your network with two network adapters,
run
Net$config and answer the questions and when it responds with
is this an Ennode or router, say its a router. Finish answering
all questions.
|
