Nemonixô Engineering, Inc. 84 October Hill Road, Holliston, MA 01746
Phone: 800-435-8650 / 508-429-3660 Fax: 508-429-3338
Electronic mail: info@nemonixengineering.com
Website: www.nemonixengineering.com

Q:HOW DO I SETUP SYCONFIG.COM
A:$!	This is an empty site-specific device configuration procedure.

$!	If you have specific device configuration requirements at your
$!	site, you should place the required commands in this procedure.
$!
$!	Use caution when placing configuration commands in this file
$!	which are only to be executed on specific nodes.  By default
$!	SYCONFIG.COM is in the cluster-common directory SYS$COMMON
$!	and is therefore executed by all nodes.
$!
$!
$!	Remove the comment from the line below if you wish to prevent
$!	VMS from configuring devices with a SYSGEN AUTOCONFIGURE ALL
$!	command.  This is typically only required if you are debugging
$!	new device drivers.
$!
$!	STARTUP$AUTOCONFIGURE_ALL == 0
$!
$!
$!+++ Entry added by Nemonix, Inc.  2-JUL-2000 14:22:13.32
$!    Additions to SYCONFIG.COM for VAX Wide UltraSCSI and Fast Ethernet
$!
$!    Note: Older SCSI disks and tapes do not support SCSI
$!          Logical Units (LUNS).  If you experience problems, 
$!          such as a physical disk appearing as several 
$!          DKW devices, try NOLUNS.
$!
$!          Some SCSI devices, such as RAID controllers require
$!          LUN support.
$!
$!              config_pci uses the following options:
$!
$!                  luns       Enable SCSI LUNS
$!                  noluns     Disable SCSI LUNS
$!
$!                  10	    Ethernet Speed = 10Mb/sec
$!                  100	    Ethernet Speed = 100Mb/sec
$!
$!                  cluster    Allow clustering on fast Ethernet Port
$!                  nocluster  Disable clustering on fast Ethernet Port
$!
$!     Nemonix VAX SCSI adapters default to a port letter of W
$!     and therefore devices will be named as follows:
$!
$!                Device Name  |  SCSI ID  |  LUN 
$!               --------------+-----------+------
$!                  DKW100     |     1     |   0  
$!                  DKW101     |     1     |   1  
$!                  DKW102     |     1     |   2  
$!                  DKWnnn     |           |      
$!                     .       |           |      
$!                     .       |           |      
$!                  DKW200     |     2     |   0  
$!                  DKW300     |     3     |   0  
$!                  DKWnnn     |           |      
$!                     .       |           |      
$!                     .       |           |      
$!                                                
$!     if this naming convention conflicts with other devices on your
$!     system, you may change the port letter to X, Y or Z, changing
$!     your device names to DKXnnn, DKYnnn or DKZnnn respectively.
$!
$!
$ mc config_pci 100 noluns nocluster 
$!
$!    The following line equates esa0 to ewa0 so that
$!    existing network applications can find the fast
$!    Ethernet Port.( NOTE THIS LINE IS COMMENT OUT FOR
$!    DECNET_PLUS)
$!
$ define/sys/exec esa0 ewa0
$!
$!    Note: In order for DECNET (ncp) to know about the
$!    fast Ethernet port, you must execute the following
$!    commands:
$!
$!    To define the fast Ethernet port in the permanent network database:
$!
$!        $mcr ncp def line sva-0 state on
$!        $mcr ncp def circ sva-0 state on
$!
$!    To define the fast Ethernet port in the volatile network database:
$!
$!        $mcr ncp set line sva-0 state on
$!        $mcr ncp set circ sva-0 state on
$!
$!    If you re-configure your network, you will need to re-issue these commands
$!
$!--- End of Entry added by Nemonix, Inc.  2-JUL-2000 14:22:13.46
$!